Our Products - Albany Steel & Brass Corp

Quick view

M5 X 25 Torx Pan Plasti-Kwick Zinc Plated (Box of 50)

VIEW SPEC SHEET HERE The Design: The Plasti-Kwick Plus design combines a 30 degree thread from, reduced root diameter and coarse thread pitch to provide the ultimate screw for plastic applications.

MSRP:

Was:

Now: $12.00

Add to Cart
Quick view

Magnetic Bit Handle 5/16

Magnetic Handle for 5/16 bits

MSRP:

Was:

Now: $15.85

Add to Cart
Quick view

Malco "Gold Standard" 2"-12" Malco Hole Cutters HC1

Distinctive gold Bits, Bearings and Pivot Pin signify the longest lasting, fastest cutting, easiest adjusting solution for cutting holes in sheet metal. Malco Hole Cutters quickly install into the chuck of any corded or cordless drill as small as 1/4" (6...

MSRP:

Was:

Now: $81.95

Add to Cart
Quick view

Malco "Gold Standard" 2"-20" Malco Hole Cutters HC2

Distinctive gold Bits, Bearings and Pivot Pin signify the longest lasting, fastest cutting, easiest adjusting solution for cutting holes in sheet metal. Malco Hole Cutters quickly install into the chuck of any corded or cordless drill as small as 1/4" (6...

MSRP:

Was:

Now: $104.35

Add to Cart
Quick view

Malco 12" Magnetic Hand Sweep MS12

Comfortable angled handle grip projects magnet forward and to the side of user for handy reach into confined areas yet keeps entire magnetic surface close to ground for efficiently picking up metal debris.Permanent magnets assure long service life and...

MSRP:

Was:

Now: $116.60

Add to Cart
Quick view

Malco Duct Stretchers

Use the Duct Stretcher to hold duct in place with one hand while slipping drive cleat in place with other hand. The low profile, straight body is designed to go anywhere, even in the tightest quarters. Additional spacing holes allow wheels to be adjusted...

MSRP:

Was:

Now: $31.85

Add to Cart
Quick view

Malco Flexible Fiberglass Duct Cutter FDC1

Built-in wire cutter lets you finish the job you started with just one tool! Double edged blade cleanly pierces through outer skin and insulation. Cuts from either direction around entire circumference of duct. Fine honed blade is long lasting stainless...

MSRP:

Was:

Now: $54.00

Add to Cart
Quick view

Malco Impact Turbo Crimper

Attention: Use Impact Driver Only! Minimum 12V DC Impact Driver With Quick Release 1/4 in. Hex Chuck. Get the competitive edge with a labor and cost saving TurboCrimper® Impact driver attachment. Based on actual field trials, the TurboCrimper Impact...

MSRP:

Was:

Now: $166.90

Add to Cart
Quick view

Malco Offset Duct Stretcher

Use the Duct Stretcher to hold duct in place with one hand while slipping drive cleat in place with other hand. OFFSET DUCT STRETCHER - Same features as DS1 plus offset handle to eliminate knuckle contact

MSRP:

Was:

Now: $33.75

Add to Cart
Quick view

Malco Pipe and Duct Holders 2DH

Like an extra pair of hands! Two powerful clamps and four feet of 125lb tensile strength linked chain. Set holds duct in place, either between or under joists until it is properly secured. Also ideal for installing fiberglass duct, link chain will not...

MSRP:

Was:

Now: $40.55

Add to Cart
Quick view

Malco Portable Mini-Brake MB48A

Make big or small fabrications on the job with this lightweight and portable tool! The versatile Mini Brake produces bends up to 135 degrees in sheet metals, including aluminum, copper and 22-gauge galvanized steel. The brake's compact size can...

MSRP:

Was:

Now: $533.00

Add to Cart
Quick view

Malco Portable Mini-Brake Optional Leg Kit MBL

Malco Portable Mini-Brake Optional Leg Kit MBL

MSRP:

Was:

Now: $123.20

Add to Cart